Resource Pack - Install on Windows

Click on a link below to go to a specific section of the software installation:

Install Requirements
Before You Begin
Install Procedure

Install Requirements

The Resource Pack is installed from a software disc as listed in software installation disc and can be installed on any client computer.

The following procedure describes the steps involved in installing the Resource Pack. If you choose to install additional components simultaneously, refer to the appropriate procedures for installation requirements and steps specific to the component. Note that when you install multiple components, the sequence of the install steps may vary.

Microsoft Visual C++ 2008 Redistributable Package is automatically installed. Note that Visual C++ 2008 Redistributable Package can co-exist with other versions of this software.

.NET Framework 2.0 is automatically installed. Note that .NET Framework 2.0 can co-exist with other versions of this software.

Before You Begin

Log on to the client as local Administrator or as a member of the Administrators group on that computer.

Install Procedure Getting Started
1.	Place the Software Installation Disc for the Windows platform into the disc drive. After a few seconds, the installation program is launched. If the installation program does not launch automatically: Click the Start button on the Windows task bar, and then click Run. Browse to the installation disc drive, select Setup.exe, click Open, then click OK. NOTES If you are installing on Windows Server Core editions, mount to Software Installation Disc through command line, go to the AMD64 folder and run Setup.exe.
2.	Choose the language you want to use during installation. Click the down arrow and select the desired language from the drop-down list, and click Next to continue.
3.	Select the option to install software on this computer. NOTES The options that appear on this screen depend on the computer in which the software is being installed.
4.	Read the license agreement, then select I accept the terms in the license agreement. Click Next to continue.
Select Components for Installation

5.	Select the component(s) to install. NOTES Your screen may look different from the example shown. Components that either have already been installed, or which cannot be installed, will be dimmed. Hover over the component for additional details. If you wish to install the agent software for restore only, select Install Agents for Restore Only checkbox. See Installing Restore Only Agents for more information. The Special Registry Keys In Use field will be highlighted when GalaxyInstallerFlags registry key is enabled. Move the mouse pointer over this field to see a list of registry keys that have been created in this computer. Click Next to continue. To install the Resource Pack, expand the following Tools folder. Then select the following: Resource Pack
Configuration of Other Installation Options
6.	If this computer and the CommServe is separated by a firewall, select the Configure firewall services option and then click Next to continue. For firewall options and configuration instructions, see Firewall Configuration and continue with the installation. If firewall configuration is not required, click Next to continue.
7.	Enter the fully qualified domain name of the CommServe Host Name. This should be TCP/IP network name. e.g., computer.company.com. NOTES The CommServe client name is the name of the computer. This field is automatically populated. Do not use space and the following characters when specifying a new name for the CommServe Host Name: \\|`~!@#$%^&()+=<>/?,[]{}:;'" If a computer has already been installed, this screen will not be displayed; instead the installer will use the same Server Name as previously specified. If you do not specify the CommServe Host Name, a window will be prompted to continue in decouple mode. Click Yes* to continue to Decoupled Install. Click No to specify a CommServe Name and continue with the installation. Click Next to continue.
8.	Enter the following: The local (NetBIOS) name of the client computer. The TCP/IP IP host name of the NIC that the client computer must use to communicate with the CommServe Server. NOTES Do not use spaces when specifying a new name for the Client. The default network interface name of the client computer is displayed if the computer has only one network interface. If the computer has multiple network interfaces, enter the interface name that is preferred for communication with the CommServe Server. If a component has already been installed, this screen will not be displayed; instead, the install program will use the same name as previously specified. Click Next to continue.
9.	Select Add programs to the Windows Firewall Exclusion List, if you wish to add CommCell programs and services to the Windows Firewall Exclusion List. NOTES: If Windows Firewall is enabled on the computer, this option is selected by default and must be enabled to proceed with the installation. If Windows Firewall is disabled on the computer, you can select this option to add the programs and services to enabled CommCell operations across the firewall, if the firewall is enabled at a later time. You can either select this option during install or add the programs and services after installation. For adding the programs and services after installation, see Configure Windows Firewall to Allow CommCell Communication. Click Next to continue.
10.	Specify the location where you want to install the software. NOTES Do not install the software to a mapped network drive. Do not use the following characters when specifying the destination path: / : * ? " < > \| # It is recommended that you use alphanumeric characters only. If you intend to install other components on this computer, the selected installation directory will be automatically used for that software as well. If a component is already installed in this computer, this screen may not be displayed. The software will be automatically installed in the same location that was previously specified. Click Browse to change directories. Click Next to continue.
Client Group Selection
11.	Select a Client Group from the list. Click Next to continue. NOTES This screen will be displayed if Client Groups are configured in the CommCell Console. For more information, see Client Computer Groups.
Schedule Automatic Update
12.	If necessary, select this option to schedule an automatic installation of software updates. NOTES Schedule Install of Automatic Updates allows automatic installation of the necessary software updates on the computer on a single or weekly basis. If you do not select this option, you can schedule these updates later from the CommCell Console. To avoid conflict, do not schedule the automatic installation of software updates to occur at the same time as the automatic FTP downloading of software updates. If a component has already been installed, this screen will not be displayed; instead, the installer will use the same option as previously specified. Click Next to continue.
Verify Summary of Install Options
13.	Verify the summary of selected options. NOTES The Summary on your screen should reflect the components you selected for install, and may look different from the example shown. Click Next to continue or Back to change any of the options. The install program now starts copying the software to the computer. This step may take several minutes to complete.
Setup Complete
14.	Setup displays the successfully installed components. NOTES The Setup Complete message displayed on your screen will reflect the components you installed, and may look different from the example shown. If you install an Agent with the CommCell Console open, you need to refresh the CommCell Console (F5) to see the new Agents. If Reboot Now button is displayed make sure to reboot the computer before performing any other operations from the computer. Click Finish to close the install program. The installation is now complete.