Manually Installing the Software on a Passive Node

Click on a link below to go to a specific section of the software installation:

Install Requirements
For passive node(s) not available while installing the software, or for a cluster with the CommServe software installed on the physical nodes and the SQL database on the virtual server, you must manually install the software on the passive node(s) now.

The following procedure describes the steps involved in installing the software on a passive node.

Install Procedure

Getting Started
1. Place the software installation disc for the Windows platform into the disc drive.

After a few seconds, the installation program is launched.

If the installation program does not launch automatically:

  • Click the Start button on the Windows task bar, and then click Run.
  • Browse to the installation disc drive, select Setup.exe, click Open, then click OK.

NOTES

  • If you are installing on a x64 version of Windows 2008 Server Core R2, go to the AMD64 folder and run Setup.exe.
  
2. In this screen, you choose the language you want to use during installation. Click the down arrow, select the desired language from the pull-down list, and click Next to continue.  
3. Select the option to install software.

NOTES

  
4. Select the option to install software on this computer.

NOTES

  • The options that appear on this screen depend on the computer in which the software is being installed.
  
5. Read the Welcome screen.

Click Next to continue, if no other applications are running.

  
6. Read the virus scanning software warning.

Click OK to continue, if virus scanning software is disabled.

  
7. Read the license agreement, then select I accept the terms in the license agreement.

Click Next to continue.

 

Cluster Selection
8. Select Configure a Virtual Server.

Click Next to continue.
9. Select the disk group in which the virtual server resides.

Click Next to continue.

10. Click OK to continue.

The registry and environment files are updated on the passive node.

Verify Summary of Install Options
11. Verify the summary of selected options.

NOTES

  • The Summary on your screen should reflect the components you selected for install, and may look different from the example shown.

Click Next to continue or Back to change any of the options.

The install program now starts copying the software to the computer. This step may take several minutes to complete.
12. The System Reboot message may be displayed. If so, select one of the following:
  • Skip Reboot
    This option will be displayed if the install program finds any files belonging to other applications, that need to be replaced. As these files are not critical for this installation, you may skip the reboot and continue the installation and reboot the computer at a later time.
  • Reboot Now
    If this option is displayed without the Skip Reboot option, the install program has found files required by the software that are in use and need to be replaced. If Reboot Now is displayed without the Skip Reboot option, reboot the computer at this point. The install program will automatically continue after the reboot.
  • Exit Setup
    If you want to exit the install program, click Exit Setup.

Schedule Automatic Update
13. If necessary, select this option to schedule an automatic installation of software updates.

NOTES

  • Install Updates Schedule allows automatic installation of the necessary software updates on the computer on a single or weekly basis. If you do not select this option, you can schedule these updates later from the CommCell Console.
  • To avoid conflict, do not schedule the automatic installation of software updates to occur at the same time as the automatic FTP downloading of software updates.
  • You may be prompted to reboot the computer before restarting services.

  • If a component has already been installed, this screen will not be displayed; instead, the installer will use the same option as previously specified.

Click Next to continue.

Install Remaining Cluster Nodes
14. To install/upgrade the software on the remaining nodes of the cluster, click Yes.

To complete the install for this node only, click No.
15. Select cluster nodes from the Preferred Nodes list and click the arrow button to move them to the Selected Nodes list.

NOTES

  • The list of Preferred Nodes displays all the nodes found in the cluster; from this list you should only select cluster nodes configured to host this virtual server.
  • Do not select nodes that already have multiple instances installed. For more information, see Multi Instancing.

When you have completed your selections, click Next to continue.
16. Type the User Name and Password for the Domain Administrator account, so that the installer can perform the remote install/upgrade of the cluster nodes you selected in the previous step.

Click Next to continue.
17. The progress of the remote install for the cluster nodes is displayed; the install can be interrupted if necessary.

Click Stop to prevent installation to any nodes after the current ones complete.

Click Advanced Settings to specify any of the following:

  • Maximum number of nodes on which Setup can run simultaneously.
  • Time allocated for Setup to begin executing on each node, after which the install attempt will fail.
  • Time allocated for Setup to complete on each node, after which the install attempt will fail.

NOTES

  • If, during the remote install of a cluster node, setup fails to complete or is interrupted, you must perform a local install on that node. When you do, the install begins from where it left off, or from the beginning if necessary. For procedures, see Manually Installing the Software on a Passive Node.
18. Read the summary for remote installation to verify that all selected nodes were installed successfully.

NOTES

  • If any node installation fails, you must manually install the software on that node once the current installation is complete. (See Manually Installing the Software on a Passive Node for step-by-step instructions.)
  • The message displayed on your screen will reflect the status of the selected nodes, and may look different from the example.

Click Next to continue.

Setup Complete
19. Setup displays the successfully installed components.

NOTES

  • The Setup Complete message displayed on your screen will reflect the components you installed, and may look different from the example shown.
  • If you install an Agent with the CommCell Console open, you need to refresh the CommCell Console (F5) to see the new Agents.
  • If Reboot Now button is displayed make sure to reboot the computer before performing any other operations from the computer.

Click Finish to close the install program.

The installation is now complete.

Post-Install Considerations

General

  • Install post-release updates or Service Packs that may have been released after the release of the software. Alternatively, you can enable Automatic Updates for quick and easy installation of updates in the CommCell® console.

Firewall

If the CommServe is configured to communicate across a firewall, the following firewall related files must be manually copied from the active node to all the passive nodes:
  • <software installation path>/<software installation folder>/Base/FwHosts.txt
  • <software installation path>/<software installation folder>/Base/FwPeers.txt
  • <software installation path>/<software installation folder>/Base/FwPorts.txt

If for some reason the passive node is currently active, make sure to stop and restart Services after copying the files.